IP Network Camera Extender

SNMP/TELNET/CLI management, Ethernet E1 & V.35 Optional, 2/4wires, G.SHDSL.bis, ATM ALL5, NAT, PPPoA, PPPoE, IP Camera Extender

IP Network Camera Extender

  

1.OverviewFBDSL1000 series IP Camera Extender is a high quality and good performance SHDSL device with standard E1, V.35 or 10/100Mbps Ethernet interfaces integrated, you can make any choice of the three interfaces in one device. Its transmission distance is extended to 4km by 1-pair twist pair at 2M speed.  FBDSL1000 is designed with 16TC-PAM code according to ITU-T G.991.2 and ITU-T G.994.1, which can improve the transmission performance and economize resource. As the new generation product, FBDSL1000 has not only the technical advantage but also very simple installation and maintenance procedure at the same time. It is the best solution for the customers. 

2.Features

Compatible with G.991.2 and G.SHDSL.bis protocol 2 wires or 4 wires optional The distance can extend to 3.7-4km with 0.4mm (AWG26) by the speed under 2Mbps for one-pair device and 4~4.5Km for two-pair device Support ATM ALL5, NAT, PPPoA, PPPoE, RIP protocol * Support up to 5.69Mbps at 2-wire cable or 11.38Mbps at 4-wire cable when set as G.SHDSL.bis protocol 10/100Base-T interface accordant with standard IEEE802.3 and 1Mbytes buffer inserted. MAC address list inserted and 4096 MAC address available. E1 interface accordant with standards as ITU-TG.703G.823 and G.742. DSL speed can be set manually or auto-detect by the DSL line Easy to install and operate. Working preferences by DIP switch and software control. AC110~240V or DC48V power supply optional.

3.Specification3.1.DSLConnector: 4 pins terminalLine Code: TC-PAMRate:192Kbps~ 2048KbpsDistance: 3.8Km   Single Pair             4.2Km   Double PairsNotice: AWG26 (0.4mm)

The following port types describe all the ports in full-configed G.SHDSL Standalone products. E1 Ethernet and V.35 ports are optional, according to users real application. To get detail part number, please refer to Order Information. The E1 Module Card only provides E1 port..

3.2.E1Compliant with ITU-T G.703, G.704, G.823Line Code: HDB3Connector: 75ohm/BNC, 120ohm/RJ45Framed and Unframed is optional

3.3.EthernetCompliant with IEEE802.3, IEEE802.3u, IEEE802.3xConnector: RJ4510/100Mbps auto-sensing, Half/Full duplex auto detectedThe Module Card doesnt provide this port.Note: see 6.4 comments.

3.4.V.35Ratenx64kbpsFlow control: User defineConnector: DB25FThe Module Card doesnt provide this port.Note: see 6.4 comments.

3.5.Management PortConnector: RS232/DB9(for Standalone Products)Connector CONSOLE/RJ45(for Module Card)Setting timeslots, clocking source, alarms, E1/DSL loop back etc.CLI interface, use hyper-terminal to management

3.6.PowerStandalone Products:AC/DC optionalAC: 220V, 50Hz±5%, Waveform Distorting Rate<5%DC: -40V~ -57VPower Consumption  < 10W

Module Card:The power supply comes from the backboard in 4U Machine-FrameDC: 15V/6APower consumption < 10W

3.7.EnvironmentOperating EnvironmentTemperature: 0~+50Humidity: 0~90, no condensing

Storage EnvironmentTemperature: -25~+70Humidity: 0~95%, no condensing

 4.Order InformationModel:FBDSL1000 E1, V.35 or 10/100Mbps port, one-pair or two-pair G.SHDSL Modem P/N (Part Number):F11-G13              One pair wire, 10/100Mbps Ethernet Interface, StandaloneF11-G15              One pair wire, E1 Interface, StandaloneF11-G16      one pair wire, V.35 interface, StandaloneF11-G1315          One pair wire, 10/100Mbps Ethernet & E1 port, StandaloneF11-G1316          One pair wire, 10/100Mbps Ethernet & V.35 port, StandaloneF11-G1516          One pair wire, 10/100Mbps Ethernet & E1 port, StandaloneF11-G131516      One pair wire, 10/100Mbps Ethernet & E1 & V.35 port, Standalone

IP Network Camera Extender